Differences

This shows you the differences between two versions of the page.

--- lwc:hardware:ciscoaironet1130 [2021/02/13 06:27] – John Harrison
+++ lwc:hardware:ciscoaironet1130 [2021/03/16 14:48] (current) – John Harrison
@@ Line 1: / Line 1: @@
 ===== General Information =====
   * serial port is 9600 baud
-  * to turn something off, put a `no` in front of the configuration
+  * to turn something off, put a ''no'' in front of the configuration
-  * to see current configuration `show configuration`
+  * to see current configuration ''show configuration''
   * you can cut/past multiple commands/settings as once
-  * see current virtual lans: `show vlan`
+  * see current virtual lans: ''show vlan''
-  * fastethernet abbreviation is `fa`
+  * fastethernet abbreviation is ''fa''
+  * change hostname: ''hostname <HOSTNAME>''
+  * ''ssh''ing in: ''ssh  -c 3des-cbc -oKexAlgorithms=+diffie-hellman-group1-sha1 <USERNAME>@<IP-ADDESS>''
+  * set the channel only with physical Radio0 and not the "virtual" radios. All the SSIDs will always be on the same channel
   * vlans appear to be intended to be used only with Cisco switchports and perhaps when they are in trunk mode
-    * it appears [[https://sites.google.com/site/chaseerry/cisco-routing/dhcp-relay-agent---one-dhcp-server-for-many-vlans|you can get around this]]
+    * it appears [[https://sites.google.com/site/chaseerry/cisco-routing/dhcp-relay-agent---one-dhcp-server-for-many-vlans|you can get around this]] by having the access point forward DHCPDISCOVER broadcast packets directly to our DHCP server using the ''ip helper-address'' command.
-<code>
+<code>router#conf t
+router(config)#int fa0.2
-==== Notes from things I tried ====
+router(config-subif)#ip helper-address address_of_server
+router(config-subif)#end
-<code>
-configure terminal
-dot11 ssid filiminAtHarrison
-ap(config-ssid)#vlan 2
-ap(config-ssid)#mbssid guest-mode
-ap(config)#dot11 ssid filiminAtWIN
-ap(config-ssid)#authentication open
-ap(config-ssid)#authentication key-management wpa version 2
-ap(config-ssid)#wpa-psk ascii testing123
------
-ap(config)#int dot11radio0
-ap(config-if)#mbssid
-ap(config-if)#encryption vlan 2 mode ciphers aes-ccm
-ap(config-if)#encryption vlan 3 mode ciphers aes-ccm
-filiminAtWIN mapped to vlan 1
-filiminAtHarrison mapped to vlan 2
 </code>
+  * 8266 with Arduino Wi-Fi library seem happiest with ''encryption mode ciphers aes-ccm''
-==== References ====
-  * https://sites.google.com/site/chaseerry/cisco-wireless/1131ag---configuring-multiple-ssids
-  * https://docs.google.com/document/d/1NgABdg-aOfQ045B2q-Q9nhHWE-Hz20dadCirKcmSM_0/edit#
-  * https://content.cisco.com/chapter.sjs?uri=/searchable/chapter/www.cisco.com/content/en/us/td/docs/wireless/access_point/12-3_7_JA/configuration/guide/i1237sc/s37ssid.html.xml#wp1050468
-  * https://groups.google.com/g/cisco2010/c/WqPtZlenuJU
-  * https://community.cisco.com/t5/wireless/wireless-ap-not-assigning-ip-address-to-new-clients/m-p/4140883#M215311
-  * https://learningnetwork.cisco.com/s/question/0D53i00000KstA2/privilege-level-when-username-command-is-configured
 ==== Multiple SSIDs example ====
@@ Line 45: / Line 23: @@
 dot11 ssid LAB2
 authentication open
-authentication key-management wpa version 2
+authentication key-management wpa
+! authentication key-management wpa version 2
 wpa-psk ascii testing123
 vlan 2
@@ Line 52: / Line 31: @@
 int dot11radio0
 mbssid
+!channel 2412
+!channel 2437
+channel 2462
 encryption vlan 2 mode ciphers aes-ccm tkip
+! encryption vlan 2 mode ciphers aes-ccm
 ssid LAB2
 no shut
@@ Line 62: / Line 45: @@
 encapsulation dot1Q 2 native
 exit
---------------------
+exit
+! --------------------
+config t
+dot11 ssid LAB3
+authentication open
+authentication key-management wpa
+! authentication key-management wpa version 2
+wpa-psk ascii testing123
+vlan 3
+mbssid guest-mode
+exit
+int dot11radio0
+mbssid
+! encryption vlan 3 mode ciphers aes-ccm tkip
+encryption vlan 3 mode ciphers aes-ccm
+ssid LAB3
+no shut
+exit
+interface dot11Radio 0.3
+encapsulation dot1Q 3
+bridge-group 1
+exit
+int fa0.3
+encapsulation dot1Q 3
+exit
+exit
+! --------------------
 config t
-dot11 ssid LAB5
+dot11 ssid LAB4
 authentication open
-authentication key-management wpa version 2
+authentication key-management wpa
+! authentication key-management wpa version 2
 wpa-psk ascii testing123
 vlan 4
@@ Line 73: / Line 83: @@
 int dot11radio0
 mbssid
-encryption vlan 4 mode ciphers aes-ccm tkip
+! encryption vlan 4 mode ciphers aes-ccm tkip
-ssid LAB5
+encryption vlan 4 mode ciphers aes-ccm
+ssid LAB4
 no shut
 exit
@@ Line 84: / Line 95: @@
 encapsulation dot1Q 4
 exit
+exit
+copy run start
 </code>
+note: see comment about vlans and switchports above. That configuration for the fastethernet **may** be required
+==== References ====
+  * https://sites.google.com/site/chaseerry/cisco-wireless/1131ag---configuring-multiple-ssids (best reference)
+  * https://docs.google.com/document/d/1NgABdg-aOfQ045B2q-Q9nhHWE-Hz20dadCirKcmSM_0/edit# (original configuration of the access points)
+  * https://content.cisco.com/chapter.sjs?uri=/searchable/chapter/www.cisco.com/content/en/us/td/docs/wireless/access_point/12-3_7_JA/configuration/guide/i1237sc/s37ssid.html.xml#wp1050468
+  * https://groups.google.com/g/cisco2010/c/WqPtZlenuJU
+  * https://community.cisco.com/t5/wireless/wireless-ap-not-assigning-ip-address-to-new-clients/m-p/4140883#M215311
+  * https://learningnetwork.cisco.com/s/question/0D53i00000KstA2/privilege-level-when-username-command-is-configured